Home automation

Hacks that I’ve done to the house

How to install and access the CM15A X10 controller in Fedora 15

Posted by on Thursday, 6 October, 2011

Following the previous post about how install and access the CM15A X10 controller in Ubuntu, I’m now publishing similar instructions for Fedora 15.
I use the mochad, Multiple Online Controllers for Home Automation Daemon.
“mochad” is a Linux TCP gateway daemon for the X10 CM15A RF (radio frequency) and PL (power line) controller and the CM19A RF controller.

To get it up and running on Fedora follow these steps.

1 ) Install libusb1 and libusb1-devel (if not already installed):
sudo yum install libusb1 libusb1-devel

2 ) Download mochad:
Visit the mochad homepage and download the latest version OR get this version that is probably not the latest but it works on Fedora 15 at the time my writing this.

3 ) Untar, compile and install mochad:
tar -zxvf mochad-0.1.12.tar.gz
cd mochad-0.1.12
./configure
make
sudo make install

Replace the mochad-0.1.12 with whatever version you download.

4 ) Plug in the CM15A device via the USB port to the box

5 ) Check that the system can see it:
lsusb
Should return a line like this:
Bus 002 Device 065: ID 0bc7:0001 X10 Wireless Technology, Inc.

The Bus and Device might be different in your case.
6 ) Launch the mochad daemon:
sudo /usr/local/bin/mochad

It should return to the prompt with no errors.

8 ) Use it!
To use the mochad daemon you can talk to it on port 1099 (by default) on the localhost using netcat (nc) like this example:
To turn on module A1
nc -c "echo pl a1 on" localhost 1099
To turn off module A1
nc -c "echo pl a1 off" localhost 1099

And that’s it. Check out the mochad homepage for further details.

ShareThis

How to install the CM15A X10 controller on Ubuntu 8.04 LTS

Posted by on Wednesday, 5 October, 2011

To access the CM15A X10 controller under Linux (Fedora or Ubuntu) I use the mochad, Multiple Online Controllers for Home Automation Daemon.
“mochad” is a Linux TCP gateway daemon for the X10 CM15A RF (radio frequency) and PL (power line) controller and the CM19A RF controller.

To get it up and running under Ubuntu 8.04 LTS “Hardy” follow these steps.

1 ) Download libusb-1.0 (because Hardy does not ship with it):
Goto libusb-1.0 website, scroll to the Download section and get the latest version if the source files.
If the latest version does not work, you might download this version that works fine under hardy.

2 ) Unpack, untar, compile and install libusb-1.0:
bzip2 -d libusb-1.0.8.tar.bz2
tar -xvf libusb-1.0.8.tar
cd libusb-1.0.8
./configure
make
sudo make install

Replace the libuse-1.0.8 part with whatever version you downloaded.

3 ) Download mochad:
Visit the mochad homepage and download the latest version or get this version that works on Hardy.

4 ) Untar, compile and install mochad:
tar -zxvf mochad-0.1.12.tar.gz
cd mochad-0.1.12
./configure
make
sudo make install

Replace the mochad-0.1.12 with whatever version you download.

5 ) Plug in the CM15A device via the USB port to the box

6 ) Check that the system can see it:
lsusb
Should return a line like this:
Bus 002 Device 065: ID 0bc7:0001 X10 Wireless Technology, Inc.

The Bus and Device might be different in your case.

7 ) Launch the mochad daemon:
sudo /usr/local/bin/mochad

It should return to the prompt with no errors.

8 ) Use it!
To use the mochad daemon you can talk to it on port 1099 (by default) on the localhost using netcat (nc) like this example:
To turn on module A1
nc -c "echo pl a1 on" localhost 1099
To turn off module A1
nc -c "echo pl a1 off" localhost 1099

And that’s it. Check out the mochad homepage for further details.

ShareThis